Tsunami.GX bridges offer sophisticated, preventative management tools to simplify network maintenance and eliminate downtime. Advanced diagnostic tools identify and isolate potential issues before they impact the network.

• Standards-based SNMP management and webbased GUI simplifies remote management and integrates easily into existing software platforms
• Built-in spectrum analyzer and an alarm log facilitate RF planning and post-deployment tuning

Backed by more than 20 years of wireless design innovation, Proxim’s Tsunami wireless bridge family easily and affordably enables network extension, redundancy and backhaul. Tsunami wireless bridges eliminate fiber installation costs and leased line fees to bring you the capacity of more than eight leased lines with the TCO of Ethernet.

• High capacity for bandwidth-intensive applications such as PBX extension, data backhaul and critical link redundancy
• No expensive recurring leased line costs
• Superior system gain ensures consistent, high quality network operation

Because Tsunami bridges operate in license-exempt ISM frequency bands, they can be deployed quickly – eliminating the long lead times associated with leasing lines or trenching new fiber optic cable. This is especially useful in network redundancy and contingency planning.

• Rapid device deployment and flexible re-deployment
• ISPs maintain business continuity, even in severe conditions
• Enterprises minimize costly business application downtime

A wireless alternative to a wired network yields quality as well as flexibility. Proxim’s Tsunami bridges offer the highest security and reliability available in networking today.

• Over 99.999% reliable RF transmission
• Meets or exceeds wired network security
• Proprietary encryption methods ensure secure data transmission

Proxim Tsunami.GX 32 Specifications

Frequency	Digital Capacity	Non-Overlapping Frequency Pairs	FCC Emmission Designator	Threshold (BER=1x10-6)	Output Power	System Gain	Distance (Miles/KM)
5725-5850 MHz	32 Mbps 24 Mbps	3 2	13M4G7D	≥85 dBm ≥86 dBm	≥23.5 dBm	≥109.5 dB, 112 dB typ. ≥108.5 dB, 111 dB typ.	42/68 44/71

System
Configuration	Split-box: IDU, RF Unit
Modulation	DSSS; QPSK
Frequency Stability	±10 ppm
RF Attenuation Range1	20 dB
Maximum Receive Signal	-20 dBm error free; 0 dBm no damage
Error Floor	<10-11
Latency (T1)2, one-way	325 µsec ±10%
Error Correction	Reed-Solomon
Security	12 character Link ID (48 bits)
Regulatory Compliance	FCC Part 15.247; IC RS210
FCC ID	HZB-S58-GX1
Industry Canada ID	1856A-U5358GX1
Digital Line Interfaces
Main Data Channel4
3-Channel Mode 2-Channel Mode	32 Mbps aggregate; 16 Mbps full duplex 24 Mbps aggregate; 12 Mbps full duplex
10/100 Base T	RJ-45 modular jack Auto-sense MDI/MDI-X
10/100 Base FX	SC-Type, multi-mode Fiber
Compliance	IEEE 802.3
Wayside Data Channels
T1/E1	DSX-1 (2 each) or CEPT-1 (2 each), software selectable RJ-48C modular jack
Compliance
Maximum Packet Size	1536 bytes
T1 E1	ANSI-1987-T1, CCITT G.823 G.703
Auxiliary Interfaces
Orderwire (DTMF)	RJ-11, 100 addresses
VF	8 pin modular jack, 4-wire 0dBm @ 600 ohm, balanced
Aux Data (serial)	8 pin modular jack, EIA-561 ≤19.2kbps, selectable, DCE
Fault and Configuration Management
Network Management	SNMP v2c (MIB II, Proxim enterprise MIBs), embedded HTML server, Telnet, VT-100 terminal
Far End Management	Via NMS (embedded router, gateway address, subnet mask), front panel display
Physical Interfaces
NMS 1	10/100BaseT, RJ-45, auto-sense
NMS 2	10/100BaseT, RJ-45, auto-sense
Configuration (serial)	EIA-574, 9600bps, 9-pin Sub-D, DTE
External Alarm Interface
Connector	9-pin Sub-D female
Outputs	2 Form C Relays (Major, Minor)
Inputs	2 TTL with internal pull-ups
Power/Environment
Input Voltage Range	-20 to -60 Vdc or +20 to +60 Vdc
Power Consumption	<70 Watts
Power Connector	3-pin terminal block
Operating Temperature
IDU	0°C to +50°C
RF Unit	-30°C to +55°C
Humidity
IDU	95%, non-condensing
RF Unit	100%, condensing
Altitude	up to 15,000 ft/5000 m
Wind Loading (RF Unit)	up to 110 mph/96 kts
MTBF IDU MTBF RF Unit	>100,000 hours >100,000 hours

Physical Dimensions
	IDU	RF Unit
Size (in/cm)	17.2 X 10.9 X 1.72 / (43.6 X 27.6 X 4.4)	14.1 X 10.9 X 1.72 / (35.8 X 27.6 X 4.4)
Weight (lbs/kg)	6.5/2.9	12.0/5.4
Mechanical
RF Unit	Antenna Port	Type-N female (outdoor RF cable not provided)
	IDU Port	TNC female
	Cable to IDU	LMR-240 or equiv. <100m LMR-400 or equiv. <200m LMR-600 or equiv. <300m
Mounting	IDU	EIA rackmount, 19” or 23”, 1RU
	RF Unit	EIA rackmount, 19”or 23”, 1RU, or outdoor pole mount
	Pole Mount Bracket (optional)
Selectable Non-Overlapping Frequency Plans
2-Channel Mode	A: 5734 / 5819 MHz B: 5756 / 5841 MHz
3-Channel Mode	A: 5731.5 / 5816.5 MHz B: 5745.0 / 5830.0 MHz C: 5758.5 / 5843.0 MHz
Ordering Information
	64765	Low Band Terminal
	64766	High Band Terminal
	ACC-GX-RF-2	Optional RF Unit Outdoor Mounting Kit
	201-31075-1	Optional AC Adapter 110/220 VAC with cable and connector
	Call for details	ServPak 24x7 Enhanced Service and Support contracts (1yr-3yr)
Shipping Configuration
Tsunami.GX 32 IDU (Indoor Unit); ISM Low Band or High Band RF Unit; IDU Indoor Rack Management Kit; ACC-GX-RF-1 RF Unit Indoor Mounting Kit (includes 12” IDU to RFU TNC-to-TNC cable); Quick Install Guide; CD-User Documentation

¹ Output power is specified at zero attenuation
² Does not include air latency of approximately 5.4 µsec/mile
³ RF Unit installed outdoors with 6ft. parabolic antenna, 99.995% one-way RF link availability, average climate/terrain, no multipath reflection. Assumes FCC regulations for EIRP.
⁴ No Waysides enabled